Geared motor MARK.SC
Residential use
Counterweight garage doors
24 Vdc
Up to 8 ㎡
Integrated device that guarantees maximum precision during the automation manoeuvring steps
Intelligent power control system that allows obtaining dynamic data through a precise calculation of the thrust. The system is able to locate any critical points and adjust the torque accordingly in relation to actual requirements and according to measured performance
433.92 MHz Receiver equipped exclusively with Advanced Rolling Code (ARC)
This is a protocol for connection with KNX home automation systems by connection of the X.BE card (optional)
Predisposition to manage the control unit using the BeUP app and pro.UP accessory which, by recreating the control unit menu, makes it possible to adjust parameters and logic, read error messages and update the firmware. It is possible to perform remote diagnostics, check the status of the gate and send commands.
64 transmitters storable inside the receiver
Identifies motors or control units with power consumption in standby mode of ≤ 0,8 W.
MARK.SC
24 Vdc | intensive use
24 Vdc gear motor for intensive use | Equipped with a service light with 14 integrated LEDs that guarantee a high light output | The operator is characterised by a compact size (48 cm length) that allows for a simplified balance of the door, an easy and quick installation even on folding counterweight garage doors | The output shaft with 20 x 20 mm through-hole panel and the wheelbase of just 53 mm enables perfect integration also with existing systems | The encoder guarantees the highest safety and precision during the movement of the door | Limit switch for the opening and integrated control buttons | Operation guaranteed even in the event of a power failure thanks to batteries | Anti-crushing system with amperometric obstacle detection | Integrated manual release system with lever
| Motor supply | 24 Vdc |
| Max absorbed current | 5,5 A |
| Torque | 300 Nm |
| Opening time | 14" ÷ 17" |
| Duty cycle | intensive use |
| Protection level | IP20 |
| Built-in control unit | |
| Integrated receiver | |
| Encoder | |
| Operating temperature | -20°C /+50°C |
| Max. door surface area 1 motor (2 motors) | 8 ㎡ (12 ㎡) |
| Weight | 7 kg |
| N. motors per pallet | 54 |
TILTY24
APPLICATION
1 or 2 actuators for tilt up doors
CONTROL UNIT POWER SUPPLY
100 ÷ 250 Vac - 50/60 Hz
MOTORS POWER SUPPLY
24 Vdc / 130 W + 130 W
POWER CONSUMPTION IN STAND-BY
0.8 W
MAIN FUNCTIONS
Integrated LCD display | Integrated radio receiver 433.92 MHz 64 codes with ARC coding | Removable terminal boards | Automatic, semi-automatic and Deadman logic | Encoder input | Step-by-step and stop inputs | Photocell input settable as input for N.C. or 8K2 sensitive edge | Two inputs configurable as open, close, photocell in opening-closing, photocell in closing, opening and closing limit switch for the second motor | Limit switch input | Separate power supply output for each motor | Output for 24 Vdc flashing light | 24 Vdc auxiliary output max 500mA | Output (230Vac 5A max) configurable as open gate signal light, courtesy light, zone light, second radio channel, photocell testing, flashing light, open gate alarm, NC input alarm | 24 Vdc service light output | Autoset operating parameters | Electronic torque adjustment | Separate electronic adjustments of opening and closing speeds | Anti-crushing safety through amperometric detection and encoder management | Electronic torque adjustment with automatic calculation for each point of the stroke (STC SYSTEM | Adjustable slowdowns in opening and closing | Built-in energy saving system ESA+ | Set up for connection to KNX systems via X.BE card (optional) | Designed for managing, configuring, diagnosing and updating firmware through the BeUP app, using the PRO.UP accessory | Advantouch system to configure parameters and manage radio transmitters | Number of manoeuvres | Programming access password | Maintenance warning | Built-in battery charger, compatible with 2 batteries 12V 1.2Ah
