Geared motor BULL624SE.S
Commercial use
24 Vdc
Up to 600 kg
Encoder signal recreated by the control unit beginning with the measurements of electric motor operation parameters. It is possible to manage slowing optimally and trace gate travel while providing the torque data in relation to its position to guarantee maximum safety
Intelligent power control system that allows obtaining dynamic data through a precise calculation of the thrust. The system is able to locate any critical points and adjust the torque accordingly in relation to actual requirements and according to measured performance
433.92 MHz Receiver equipped exclusively with Advanced Rolling Code (ARC)
This is a protocol for connection with KNX home automation systems by connection of the X.BE card (optional)
Predisposition to manage the control unit using the BeUP app and pro.UP accessory which, by recreating the control unit menu, makes it possible to adjust parameters and logic, read error messages and update the firmware. It is possible to perform remote diagnostics, check the status of the gate and send commands.
2048 transmitters storable inside the receiver
Identifies motors or control units with power consumption in standby mode of ≤ 0,8 W.
BULL624SE.S
24 Vdc | intensive use
24 Vdc gear motor for intensive use, with magnetic limit switches, integrated control unit and virtual encoder | Switching power supply 115/230 Vac which reduces energy consumption and ensures a long lifespan of the actuator | The main control unit, on the top part of the motor, makes it possible to facilitate the wiring procedure | The virtual encoder enables optimal management of slowing-down phases, movement tracking (STC system) and torque management in relation to the position of the gate, guaranteeing maximum safety | Operation guaranteed even in the event of a power supply failure through batteries that can be perfectly integrated in the motor| Anti-crushing system with amperometric obstacle detection | Designed for the connection of the X.BE accessory in order to be integrated with KNX domotics installations and the programming through the app BeUP and the interface PRO.UP
Reinforced foundation plate Dima included. Dimensions 326x164.5x2 mm, motor fixing distance 301x75 mm, 4 holes Ø 8.5 mm
| Power supply | 115 / 230 Vac (50-60Hz) |
| Motor supply | 24 Vdc |
| Max absorbed current | 3.3 / 1.8 A |
| Maximum thrust | 650 N |
| Opening speed | 5.5 ÷ 14 m/min |
| Duty cycle | intensive use |
| Protection level | IP44 |
| Built-in control unit | |
| Integrated receiver | |
| Encoder | |
| Virtual encoder | |
| Magnetic limit switches | |
| Pinion for rack | M4 Z14 |
| Operating temperature | -20°C /+50°C |
| Lubrication | GREASE |
| Maximum gate weight | 600 kg |
| Weight | 8.6 kg |
| N. motors per pallet | 40 |
CP.B24-D120
APPLICATION
1 actuator for sliding door series BULL SE
CONTROL UNIT POWER SUPPLY
115 or 230 Vac (selectable) 50/60Hz
MOTORS POWER SUPPLY
24 Vdc / 9 A
POWER CONSUMPTION IN STAND-BY
0.8 W
MAIN FUNCTIONS
Integrated LCD display | Integrated radio receiver 433.92 MHz 2048 codes with ARC coding | Removable terminal boards | Automatic, semi-automatic and Deadman logic | Motor limit switch inputs | Photocell input (PHO) active in opening and closing | Photocell input (PHC) active only in closing phase | Input for N.C. or 8K2 sensitive edge | OPEN input configurable as pedestrian | Two outputs configurable as open gate signal light, courtesy, zone light, second radio channel, photocell testing, flashing light, alarm contact | Output for connecting the flashing light | Predesigned for the operation of opposed sliding gates through SIS synchronisation board (optional) | Set up for connection to KNX connection through X.BE board (optional) | Designed for managing, configuring, diagnosing and updating firmware through the BeUP app, using the PRO.UP accessory | Autoset of operating parameters | Electronic torque adjustment with automatic calculation for each point in the stroke (STC SYSTEM) | Separate electronic adjustments of opening and closing speeds | Anti-crushing safety through amperometric detection | Virtual encoder | Adjustable slow-downs | Built-in energy saving system ESA+ | Advantouch system to configure parameters and manage radio transmitters | Number of manoeuvres | Programming access password | Maintenance warning | Built-in battery charger, compatible with batteries model DA.BT2/DA.BT6
