Geared motor SAM.24
24 Vdc
Up to 2.5 m per door leaf
Integrated device that guarantees maximum precision during the automation manoeuvring steps
Integrated device that guarantees maximum precision during the automation manoeuvring steps
Intelligent power control system that allows obtaining dynamic data through a precise calculation of the thrust. The system is able to locate any critical points and adjust the torque accordingly in relation to actual requirements and according to measured performance
433.92 MHz Receiver equipped exclusively with Advanced Rolling Code (ARC)
This is a protocol for connection with KNX home automation systems by connection of the X.BE card (optional)
Predisposition to manage the control unit using the BeUP app and pro.UP accessory which, by recreating the control unit menu, makes it possible to adjust parameters and logic, read error messages and update the firmware. It is possible to perform remote diagnostics, check the status of the gate and send commands.
512 transmitters storable inside the receiver
Identifies motors or control units with power consumption in standby mode of ≤ 0,8 W.
SAM.24
24 Vdc | intensive use
24 Vdc electromechanical operator for intensive use | Ideal for swing gates with large columns and leaf hinges up to 280 mm deep (just 170 mm wide) | The encoder guarantees maximum safety and precision while the gate is moving | Sturdy arm fitted with a closing lock that helps define the limit switch position during installation | Motor fixing bracket fitted with cable gland | Operation guaranteed even in the event of a power supply failure through batteries that integrate perfectly into the motor | Amperometric sensor obstacle detection system to prevent crushing | Option of adjustable flush release that allows opening from the outside in the event of a power supply failure
|
1x |
SAM.E24 24 Vdc electromechanical operator for intensive use with integrated control unit and receiver |
|
1x |
SAM.24 24 Vdc electromechanical operator for intensive use |
|
2x |
SAM.BA Articulated arm |
|
1x |
PUPILLA.T Pair of adjustable photocells with three positions, power supply 14÷30 Vac / 12÷30 Vdc | Option to mount 2 pairs close together without synchronization |
|
1x |
LAMPY Flashing light 12 ÷ 255 Vac / 14 ÷ 255 Vdc with integrated antenna |
|
1x |
TO.GO2VA 2-channel 433.92 MHz transmitter with Advanced Rolling Code and Rolling Code |
| Motor supply | 24 Vdc |
| Max absorbed current | 5.5 A |
| Torque | 220 Nm |
| Opening time | 14” (including slowdown) |
| Duty cycle | intensive use |
| Protection level | IP44 |
| Built-in control unit | |
| Encoder | |
| Mechanical stop in opening | adjustable |
| Mechanical stop for closing | optional |
| Operating temperature | -20°C /+50°C |
| Lubrication | GREASE |
| Leaf max dimension | 2.5 m |
| Weight | 6 kg |
| N. motors per pallet | 45 |
| Kit weight | 17 kg |
| N. kits per pallet | 20 |
BRAINY24
APPLICATION
1 or 2 actuators for swing gates, opposed sliding gates, and industrial folding doors with a maximum of 2 sections
CONTROL UNIT POWER SUPPLY
230 Vac - 50/60 Hz
MOTORS POWER SUPPLY
24 Vdc / 120 W + 120 W
MAIN FUNCTIONS
Integrated LCD display | Integrated 433.92 MHz 64-code receiver with 3 encoding systems (Advanced Rolling Code, Rolling Code, Fixed Code) | Removable terminal boards | Separate limit switch inputs for each motor | Open, close, and pedestrian inputs | Photocell inputs in opening-closing and in closing phases | Input for N.C. or 8K2 sensitive edge | Output for electric lock 12 Vdc | Output for configuration as gate open indicator, service light, second radio channel and photocell testing | Output for connecting flashing light | Autosetting of operating parameters | Separate electronic torque adjustment for each motor | Anti-crushing safety through amperometric detection and encoder management | Separate adjustable slowdowns for each motor in opening and closing phases | Advantouch system to configure parameters and manage radio transmitters | Number of maneuvers | Programming access password | Maintenance warning
BRAINY24 PLUS
APPLICATION
1 or 2 actuators for swing gates, opposed sliding gates, and industrial folding doors with a maximum of 2 sections
CONTROL UNIT POWER SUPPLY
115 or 230 Vac (selectable) 50/60Hz
MOTORS POWER SUPPLY
24 Vdc / 240 W + 240 W
MAIN FUNCTIONS
Integrated LCD display | Integrated radio receiver 433.92 MHz 64 codes and 3 encoding systems (Advanced Rolling Code, Rolling Code, Fixed Code | Removable terminal boards | Separate limit switch inputs for each motor | Open, close, step-by-step and pedestrian inputs | Separate opening-closing and closing photocell inputs | Stop input | Input for N.C. or 8K2 sensitive edge | Encoder Input for 24 Vdc hydraulic motors | Output for 12 Vdc electric lock | 2 outputs configurable as open gate indicator, second radio channel, courtesy light, zone light or photocell testing, flashing light, open gate alarm, NC input alarm | Output for connecting flashing light | Autoset of operating parameters | Separate electronic torque adjustment for each motor | Separate electronic speed adjustment for each motor | Anti-crushing safety through amperometric detection and encoder management | Separate slowdowns for each motor in opening and closing phases | Set up for connection to KNX systems via X.BE card (optional) | Designed for managing, configuring, diagnosing and updating firmware through the BeUP app, using the PRO.UP accessory | Advantouch system to configure parameters and manage radio transmitters | Number of manoeuvres | Programming access password | Maintenance warning | Built-in battery charger
TRUST24
APPLICATION
1 or 2 actuators for swing gates
CONTROL UNIT POWER SUPPLY
100 ÷ 250 Vac - 50/60 Hz
MOTORS POWER SUPPLY
24 Vdc / 130 W + 130 W
POWER CONSUMPTION IN STAND-BY
0.8 W
MAIN FUNCTIONS
Integrated LCD display | Integrated radio receiver 433.92 MHz 512 codes with ARC coding | Removable terminal boards | Separate limit switch inputs for each motor | Automatic, semi-automatic and Deadman logic | Separate encoder inputs for each motor | Open, close, step-by-step and pedestrian inputs | Input for programmable photocell active in opening-closing and photocell active only in closing | Input for N.C. or 8k2 sensitive edge | Output for electric lock 12/24 Vdc | Two outputs configurable as open gate signal light, courtesy light, zone light, second radio channel, photocell testing, flashing light, alarm contact | Autoset operating parameters | Separate electronic torque adjustment for each motor| Anti-crushing safety through amperometric detection and encoder management | Electronic torque adjustment with automatic calculation for each point of the stroke (STC SYSTEM) | Separate adjustable slowdowns for each motor | Possibility of encoder- or time-based operation (managed through virtual encoder) even independently between the two motors | Built-in energy saving system ESA+ | Set up for connection to KNX systems via X.BE card (optional) | Designed for managing, configuring, diagnosing and updating firmware through the BeUP app, using the PRO.UP accessory | Advantouch system to configure parameters and manage radio transmitters | Number of manoeuvres | Programming access password | Maintenance warning | Built-in battery charger
