Geared motor SAM.E24
24 Vdc
Up to 2.5 m per door leaf
Integrated device that guarantees maximum precision during the automation manoeuvring steps
Integrated device that guarantees maximum precision during the automation manoeuvring steps
Intelligent power control system that allows obtaining dynamic data through a precise calculation of the thrust. The system is able to locate any critical points and adjust the torque accordingly in relation to actual requirements and according to measured performance
433.92 MHz Receiver equipped exclusively with Advanced Rolling Code (ARC)
This is a protocol for connection with KNX home automation systems by connection of the X.BE card (optional)
Predisposition to manage the control unit using the BeUP app and pro.UP accessory which, by recreating the control unit menu, makes it possible to adjust parameters and logic, read error messages and update the firmware. It is possible to perform remote diagnostics, check the status of the gate and send commands.
512 transmitters storable inside the receiver
SAM.E24
24 Vdc | intensive use
24 Vdc electromechanical operator for intensive use with integrated control unit and receiver | The control unit, accessible from above, is positioned on a removable support that facilitates installation operations and provides quick access to the mechanical stops | 100 ÷ 250 Vac switching power supply that reduces consumption and ensures the long life of the actuator | Ideal for swing gates with large columns and leaf hinges up to 280 mm deep (just 170 mm wide) | The encoder guarantees maximum safety and precision while the gate is moving | STC System device that enables torque management in relation to the position of the gate, guaranteeing maximum safety | Sturdy arm fitted with a closing lock that helps define the limit switch position during installation | Motor fixing bracket fitted with cable gland | Operation guaranteed even in the event of a power supply failure through batteries that integrate perfectly into the motor | Amperometric sensor obstacle detection system to prevent crushing | Can be connected with the X.BE module for the integration of KNX home automation systems and programmed via the BeUP app and PRO.UP interface | Option of adjustable flush release that allows opening from the outside in the event of a power supply failure
Arm not included
|
1x |
SAM.E24 24 Vdc electromechanical operator for intensive use with integrated control unit and receiver |
|
1x |
SAM.24 24 Vdc electromechanical operator for intensive use |
|
2x |
SAM.BA Articulated arm |
|
1x |
PUPILLA.T Pair of adjustable photocells with three positions, power supply 14÷30 Vac / 12÷30 Vdc | Option to mount 2 pairs close together without synchronization |
|
1x |
LAMPY Flashing light 12 ÷ 255 Vac / 14 ÷ 255 Vdc with integrated antenna |
|
1x |
TO.GO2VA 2-channel 433.92 MHz transmitter with Advanced Rolling Code and Rolling Code |
| Power supply | 100 ÷ 250 Vac (50-60Hz) |
| Motor supply | 24 Vdc |
| Max absorbed current | 3.5 ÷ 1.9 A |
| Torque | 220 Nm |
| Opening time | 14” (including slowdown) |
| Duty cycle | intensive use |
| Protection level | IP44 |
| Built-in control unit | |
| Encoder | |
| Mechanical stop in opening | adjustable |
| Mechanical stop for closing | optional |
| Operating temperature | -20°C /+50°C |
| Lubrication | GREASE |
| Leaf max dimension | 2.5 m |
| Weight | 7,9 kg |
| N. motors per pallet | 45 |
| Kit weight | 17 kg |
| N. kits per pallet | 20 |
CP.SAM
APPLICATION
2 actuators for SAM series swing gates
CONTROL UNIT POWER SUPPLY
230 Vac - 50/60 Hz
MOTORS POWER SUPPLY
24 Vdc / 5.5 A + 5.5 A
POWER CONSUMPTION IN STAND-BY
0.8 W
MAIN FUNCTIONS
Integrated LCD display | Integrated radio receiver 433.92 MHz 512 codes with ARC coding | Removable terminal boards | Automatic, semi-automatic and Deadman logic | Separate encoder inputs for each motor | Open, close, step-by-step and pedestrian inputs | Input for active photocell in opening-closing and active photocell only in closing | Input for N.C. or 8K2 sensitive edge | Output for electric lock 12/24 Vdc | Two outputs configurable as open gate signal light, courtesy or zone light, second radio channel, photocell testing, flashing light, alarm contact | Autoset of operating parameters | Separate electronic torque adjustment for each motor| Anti-crushing safety through amperometric detection and encoder management | Electronic torque adjustment with automatic calculation for each point of the stroke (STC SYSTEM) | Separate adjustable slowdowns for each motor | Possibility of encoder- or time-based operation (managed through virtual encoder) even independently between the two motors | Built-in energy saving system ESA+ | Set up for connection to KNX systems via X.BE card (optional) | Designed for managing, configuring, diagnosing and updating firmware through the BeUP app, using the PRO.UP accessory | Advantouch system to configure parameters and manage radio transmitters | Number of manoeuvres | Programming access password | Maintenance warning | Built-in battery charger, compatible with 2 batteries 12V 1.2Ah
